• Download the wiring diagram

• Download the wiring diagram

• Download the wiring diagram

• Download the wiring diagram

Please refer to the ON/OFF Lighting Relay Switch user guide.

1. Put the ON/OFF Lighting Relay Switch in « Pairing mode ». Select the channel you want to pair.
2. You have 30 seconds to insert or remove the card from the reader. The movement of the card done during the pairing process is the movement which will switch ON the selected channel. The opposite movement will switch OFF the selected channel.
3. To initialize the ON/OFF Lighting Relay Switch, insert and remove (or remove and insert) the card.

To unpair this controller:

1. Put the ON/OFF Lighting Relay Switch in « Pairing mode ». Select the channel you want to unpair.
2. Insert or remove the card. The emitter can’t control the selected channel of the ON/OFF Lighting Relay Switch anymore.

1. Put the ON/OFF Lighting Relay Switch in « Pairing mode ». Select the channel you want to pair.
2. Make the relevant movement with the handle according to your need. Check below table.
   Note: “Bottom hung” and “Open” position are identically considered

To unpair this controller:

1. Put the ON/OFF Lighting Relay Switch in « Pairing mode ». Select the channel you want to unpair.
2. Make any kind of movement with the handle. The emitter can’t control the selected channel of the ON/OFF Lighting Relay Switch anymore.

1. Put the ON/OFF Lighting Relay Switch in « Pairing mode ». Select the channel you want to pair.
2. Press on the « learning » button of the opening sensor. The position (close or far) of the magnet from the sensor when the « learning » button is pressed is the position which will switch ON the selected channel. The opposite position will switch OFF the selected channel. Check the table below.

To unpair this controller:

1. Put the ON/OFF Lighting Relay Switch in « Pairing mode ». Select the channel you want to unpair.
2. Press on the « learning » button. The controller can’t control the selected channel of the ON/OFF Lighting Relay Switch anymore.

1. The status of the ON/OFF Lighting Relay Switch (ON or OFF) chose before put in « Pairing mode » will be associated to a presence detection.
2. Put the ON/OFF Lighting Relay Switch in « Pairing mode ». Select the channel you want to pair.
3. Press on the « learning » button of the opening sensor. When a presence is detected, the selected channel will be in the state (ON or OFF) defined at step 1. When no presence is detected, the selected channel will be in the opposite state. Check the table below.

To unpair this controller:

1. Put the ON/OFF Lighting Relay Switch in « Pairing mode ». Select the channel you want to unpair.
2. Press on the « learning » button. The controller can’t control the selected channel of the ON/OFF Lighting Relay Switch anymore.

For the pairing process of the ON/OFF Lighting Relay Switch with the gateway, please refer to the user guide of your home automation gateway.
Below, a standard learning process:

1. Put your gateway in learning mode
2. Put the ON/OFF Lighting Relay Switch in « Pairing mode » (refer to the user guide). No need to select a channel, the gateway will learn both channel during the same procedure.
3. The interface of your gateway will confirm the success of the pairing process.
   Note: To unpair the ON/OFF Lighting Relay Switch, the procedure is the same.

When wired wall switch(es) are connected to I1 and/or I2 inputs, the wall switch(es) can then act as an EnOcean controller (sending RPS telegrams).
It means that once set-up, the wired wall switch(es) can control the ON/OFF Lighting Relay Switch on which they are plugged and any other EnOcean compatible receivers wirelessly, such as the NodOn® Smart Plug.

To pair the ON/OFF Lighting Relay Switch with another receiver:

1. Put the receiver in « Pairing mode » (Ex: Smart Plug…).
2. Do a single push on the wired wall switch’s rocker you want to pair with the receiver. The status (ON or OFF) of the related output of the ON/OFF Lighting Relay Switch (S1 or S2) at the end of the pairing process with define the « ON » state of the paired receiver.

Example
If you want your receiver to be synchronized with your ON/OFF Lighting Relay Switch, pair the rocker by switching ON the related output. If you want your receiver to be desynchronized with your ON/OFF Lighting Relay Switch, pair the rocker by switching OFF the related output.

To unpair the ON/OFF Lighting Relay Switch with another receiver:

1. Put the receiver in « Pairing mode ».
2. Do a single push on the wired wall switch’s rocker paired with the receiver.

The ON/OFF Lighting Relay Switch can be locally switched ON or OFF, through a short press on the local button. This action will toggle both output at the same time.

The repeater mode has to be activated with the module under power supply.
When the repeater mode is activated, the ON/OFF Lighting Relay Switch will repeat all the messages from EnOcean network, and so increase the range of equipment around it.
The repeater mode has 3 levels:
Level 0: repeater mode is deactivated
Level 1: the signal is repeated (1 jump, see figure 1)
Level 2: the signal is repeated (2 jumps, see figure 1)
Warning: by default during the first installation the repeater mode is at level 0.
Incrementation of the three levels for repeater mode:

Working principle for repeater mode (figure 1):

Access to repeater’s next level:

Level 0 to level 1:
1 – Do 2 short presses.
2- The module LED blinks twice in green, confirming the activation of repeater’s next level.

Level 1 to level 2:
1 – Do 2 short presses.
2- The module LED blinks three times in green, confirming the activation of repeater’s next level.

Level 2 to level 0 (repeater mode is deactivated):
1 – Do 2 short presses.
2- The module LED blinks once in green, confirming the repeater’s mode deactivation.