Products

Control your electric radiators and heated towel rails via Zigbee with the FPS-4-1-00 actuator

Actionneur Chauffage Électrique Zigbee NodOn FPS-4-1-00 fixé au mur à côté d'un sèche-serviettes électrique dans une salle de bain

Pilot wire radiator, convector without pilot wire, heated towel rail or water heater: the FPS-4-1-00 actuator mounts on the wall, right at the appliance's cable outlet, and connects it to your Zigbee gateway or building management system (BMS). Along the way, it measures energy consumption and room temperature.


The problem: electric heating your smart home can't reach

In many homes and small commercial buildings, electric radiators are still adjusted one by one, directly on the appliance. There's no way to schedule them precisely, switch them off when a window opens or find out how much they actually consume. And when a control module does exist, it often has to be fitted behind the radiator or installed in the consumer unit.

The NodOn Zigbee Electric Heating Actuator tackles the problem where the appliance's cable comes out of the wall: it mounts on the wall, connects in minutes and makes the radiator controllable from your home automation system.


The FPS-4-1-00: an all-in-one actuator for electric heating

In a 90 × 90 × 32 mm wall-mounted housing, the actuator combines a 6-order pilot wire interface, a 16 A ON/OFF relay, energy metering and a temperature sensor. It communicates via Zigbee 3.0 with your gateway or BMS.

🔥
6-order pilot wire
Comfort, Comfort -1 °C, Comfort -2 °C, Eco, Frost protection and Off, for any electric radiator or heated towel rail fitted with a pilot wire
🔌
16 A ON/OFF relay
Up to 3680 W to switch a radiator without pilot wire, a water heater or any other electrical appliance
📊
Energy metering
Instantaneous power and cumulative energy of the connected appliance, from 0 to 3680 W (±5%, 1 W resolution)
🌡️
Temperature sensor
A probe measures room temperature (0 to 60 °C) and reports it to your gateway, if the gateway supports it
Key point: the actuator is mounted on the wall, as close as possible to the appliance, at its cable outlet. There's no need to work in the consumer unit or fit a module behind the radiator, and being so close gives it a better Zigbee signal (up to 40 m indoors).

Installation: with or without pilot wire

The actuator's terminal block has three terminals: N (neutral), L (live) and FP (pilot wire). A 1 m flexible cable (2 × 1.5 mm²) is supplied for the power supply. Depending on the appliance to be controlled, there are two wiring options:

Option 1
Pilot wire radiator
Connect the live, neutral and pilot wire of the radiator or heated towel rail to terminals L, N and FP. The appliance is then controlled with the 6 pilot wire orders, while still benefiting from energy metering.
Option 2
Radiator without pilot wire, water heater…
Connect only the live and neutral to terminals L and N, leaving the FP terminal unconnected. The appliance is switched ON/OFF by the built-in relay, up to 16 A.
⚠️ Electrical safety: switch off the power at the consumer unit before any work and do not connect the earth to the actuator's terminal block. The product is for indoor use only. If you are not comfortable with electrical installations, call a qualified electrician.

Setup in 3 steps

1
Mounting and wiring
With the power off, loosen the retaining screw to unclip the cover, unscrew the cable gland and fix the actuator to the wall (fixings not included). Connect the appliance's wires to the terminal block, pass the cable through the cable gland and tighten it, then clip the cover back on before restoring the power.
2
Adding it to your Zigbee network
When powered up, the LED flashes orange: the actuator is looking for a Zigbee network. Start device discovery on your gateway (Home Assistant, Jeedom, Zigbee2MQTT…). Once pairing succeeds, the LED turns green. If no network is found within 15 minutes, it stays solid orange: a short press on the button restarts the search. The actuator appears as a Zigbee smart plug (Device ID Smart Plug 0x0051).
3
Control and automations
From your interface, you select the pilot wire mode or the relay state, and monitor power, energy consumed and, if your gateway supports it, room temperature. On the actuator itself, a short press cycles through the pilot wire modes and a press of more than 3 seconds switches the relay on or off. Note: the relay must be on to control a radiator via the pilot wire.

What you can automate

🕐 Scheduling Comfort and Eco modes by time of day and day of the week 🚪 Switching to Frost protection or turning the heating off as soon as a window is opened
👤 Adjusting the heating to whether the room is occupied 🚿 Running a water heater during off-peak hours or on solar surplus, while tracking its consumption

The product

The FPS-4-1-00 mounts on the wall next to the appliance it controls and communicates directly with your Zigbee gateway or BMS.

Actuator
FPS-4-1-00
Zigbee Electric Heating Actuator
View product →
Key specifications
Modes: ON/OFF + 6-order pilot wire
Relay: 16 A resistive (3680 W)
Metering: 0 – 3680 W (±5%)
Protocol: Zigbee 3.0, OTA updates
Dimensions: 90 × 90 × 32 mm

Resources

📄 Product page
📖 User guide [FR / EN]
📊 Datasheet [EN]
🔗 FPS-4-1-00 on Zigbee2MQTT [EN]

Reading next

Compteur d'énergie 3CT Zigbee NodOn SEM-4-3-20 avec ses trois pinces ampéremétriques
Module chauffage fil pilote Zigbee NodOn SIN-4-FP-21 installé dans la sortie de câble d'un radiateur électrique

Leave a comment

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.